home Cards

Code 5d washing machine samsung. SUD error in Samsung washing machine. Causes of damage

If once again you threw laundry into the drum washing machine and launched the program, and the Samsung machine stopped after a few minutes, showing the SUD code on the display, then do not rush to call somewhere. After reading everything to the end, you will surely find the cause of this situation, perhaps eliminate it yourself. About everything in order.

Error value

Those who are fluent in English may well understand what the SUD error informs the user about. These three letters are taken from the word SUDS, which means soap foam. It is not difficult to guess that this code did not appear by chance, but because there was too much of this foam in the car. In more detail, this error means that the washing machine has switched to the mode of eliminating large foaming in the drum. Just for everything, she stopped for 5-10 minutes so that this foam settled, and then the washing process continued.

Not all Samsung washing machines have a Sud error, but this does not mean that nothing happens with increased foaming. It's just that in different models of washers the codes of the same error are different. The analogue of this error are codes 5d and Sd, this is the same thing, because the number 5 and the letter s are indistinguishable on the small display of the equipment.

Note that even without knowing the exact decoding of the code, you can understand the reason for stopping the machine if you carefully look at the drum. You can't help but notice the large amount of foam.

Reasons for the appearance

On Samsung washing machines, the sud error can be caused by various reasons. The main one is related to the powder. The reason is as follows:

using a powder that is not intended for an automatic machine. The fact is that defoamers are added to special machine powders, but they are not in powders for hand washing, so they cannot be poured into the washing machine;
fake low quality powder;
powder dosage exceeded. If things are voluminous, it is better to reduce the rate of laundry detergent, or use a special powder. And if the powder is concentrated, then it generally needs to be poured strictly according to the dosage.

If the powder you use is beyond doubt, then the whole thing is a malfunction of the washing machine. These faults include:

breakdown of the foam sensor;
failure of the pressure switch;
partial blockage in the elements of the drain system (hose, pipe, sewer);
failure of the control board, which happens extremely rarely.

What to do yourself, and what to turn to the master?

You can fix most of the causes that caused the Sud error to appear on your own. The most important thing is to act consistently. First of all, wait until the washing machine itself tries to remove the foam. If the error is still on the display, then do the following:

press the off button, then turn off the power to the machine;
open the drum and take out the laundry;
the door may be blocked, then drain the water from the tank through the emergency drain at the bottom of the machine or through the filter;
Be careful, prepare rags and a flat container into which you will pour water.
rinse the drain filter and run an idle program (without laundry and powder) with water heated to 60 0 C to wash out the remaining powder from the machine.

If the sud message reappears during the execution of this mode, then with a high probability we can talk about a breakdown of the foam sensor. It is not available in all models of washing machines, and in some machines its function is performed by a water level sensor, which is often called a pressure switch. The foam sensor cannot be repaired and must be replaced. With this problem, you should contact the master, who will find the necessary similar part and install it correctly.

If the pressure switch breaks down, you can do the repair yourself. This detail is quite easy to change, you need:

remove the top case cover;
in the upper corner of the washing machine, find the water level sensor;
remove the air duct;
disconnect flash drives with wires;
connect a new part;
assemble the machine.

In some cases, the system may issue a Sud error if the foam does not leave the drum due to a partial blockage in the hose or drain pipe. These parts need to be cleaned. The drain hose is disconnected from the machine and cleaned using a cleaning cable. To rinse the pipe, you need to get it out of the machine. You can do this through the bottom of the washer, you need

put the equipment on its side;
if there is a bottom, remove it carefully;
unclench the clamps on the pipe that hold it to the tank and pump;
rinse the part and return to its place.

You may need new clamps after cleaning the pipe, they usually change.

As for the “brain” of the machine, or rather the electronic board, we always recommend contacting the master with this problem. Both repair and replacement of this part have their own nuances, which cannot be neglected, otherwise you can harm the equipment even more. But don't worry ahead of time. If the display shows a sud error, the chances of the control module failing are very low.

Thus, in most cases, you can fix the causes that generated the sud error yourself. The main thing is to be patient and act according to the plan. Good luck!

Manufacturers of ultra-modern household appliances brand "Samsung" equipped the central control panel of the display with a button to remove errors. This function allows you to individually detect, and in some cases, eliminate the problem on your own. In this article, we will try to figure out what to do if an error occurs on the Samsung 5D washing machine, to find ways to solve the problem.

Error “Sud” (Sd, 5D) on the display of the washing machine - code meaning

In modern models of the Samsung brand, the process of foam formation is controlled. If there is an increased abundance of detergent in the rotating drum or in the container for washing powder, the function of stopping the formation of foam is activated. The illuminated error code “SUD” (SD, 5D) on the central control panel indicates that the amount of foam is not decreasing. In this situation, the washing appliance stops its programming process and starts the standby mode. This can happen due to improper use of equipment.

Important! In this case, no hasty actions need to be taken, since the code error brings only information to the attention, and after a while the selected program starts again, and the washing procedure continues.

Causes of the SUD/SD Error

There are several reasons for the error to occur on the Samsung 5d / SUD / SD washing machine. The most common include:

Using the wrong powder. If, in the absence of a special detergent, you decided to use what was at hand in case of an urgent need to wash, this is most likely the problem. Read everything in detail about.
The use of highly concentrated detergents, which is completely unsuitable for Samsung washing machines.
Too much use of detergent. For example, program washing woollens requires much less detergent.

Important! Be sure to follow the instructions for using the detergent, which are described on the package, otherwise - too much can lead to damage to the washing machine. Usually, 2 tablespoons of detergent are used for 6 kg of dry laundry.

The use of low-quality and fake detergents, which very quickly make the washing machine unusable.

Important! If you do not want to spoil the washer, it is better to always purchase only proven detergents that are from a well-known manufacturer. It is worth being wary of cheap and incomprehensible brands.

To find really high-quality, use the information from the following articles:

Other 5D error issues

In addition, there are other problematic issues. The main reasons for this error on the Samsung 5D washing machine can be:

Filter contamination - also leads to excessive formation of foam. Cleaning the water pouring cord instantly solves this problem. To quickly solve this problem, if you have never encountered it before, the instructions from the article will help.
Breakage of the foam sensor, which should be checked for operability and replaced if necessary.

Important! Household appliances need a high-quality detergent. It is advisable to replace an unsatisfactory washing and washing agent.

What to do?

Sometimes there is a moment when the washing process does not end, the foam does not disappear, and the code error button is constantly lit on the control panel. In this case, you must proceed in this order:

Stop the express wash procedure and load the liquid pouring program. It is also possible to release the appliance lock and remove unwashed laundry.
Next - after cleaning the cord for pouring water, start an idle long program mode at 60 degrees. This procedure frees the water pouring system from excess detergents.

Important! If you repeatedly display a code error on the Samsung 5D washing machine, you will have to realize the seriousness of this problem and contact a highly qualified specialist.

Possible malfunctions requiring repair

It is very rare for experienced technicians to encounter faults that require repair when the display shows washing machine Samsung errors 5D, SD or SUD. Such cases do happen, so you should be prepared.

The main signs and causes of malfunctions:

During the washing process, a 5D / SUD / SD error is generated on the Samsung washing machine, and the drum is without foam, and the error does not disappear even when household appliances are running without linen and detergent. This all indicates a malfunction of the foam sensor, which just needs to be replaced.
Error 5D / SUD / SD is displayed when turned on, washed or rinsed, but there is no foam in the drum and the error does not disappear when restarted - quite rarely this indicates a malfunction of the control unit. In the event of a burnout of the processor of the control board, only the replacement of the unit will help, otherwise, you can get by with repairs.
When the machine is turned on or during washing, the 5D / SUD / SD error pops up on the display. It is necessary to replace the water level sensor (pressure switch), which, in addition to the main function - measuring the amount of water, can also be responsible for foaming.
When you start washing without powder, household appliances drain water for a long time, but the process is normal, but if you start it with powder, a 5D / SUD / SD error appears. This indicates a blockage in the sewer, drain pipe or hose, as water can seep in and there is not enough hole for the foam. In this case, you need to clean the clogged place from foreign objects. Most often it takes several simple actions described in the article at the link to .

Important! If it is impossible to eliminate the problem on your own, you should seek help from experienced specialists.

Samsung washing machine errors

Errors on the washing machine are classified depending on the type of problem and the cause of the problem. Thanks to the automation of the Samsung washing machine, you can independently identify the problem and try to solve it:

4E, E1 - indicates an error during the filling of water. Lack of water, too low pressure in the water supply, malfunction of the electronic controller, damaged valves, broken water level sensor - all this can cause this error.
5E, E2 - shows that for a certain time the water from the tank did not have time to drain. This error on the washing machine may occur due to a clogged drain path, hose or filter, a malfunction of the drain pump or electronic controller, or a breakdown of the water level sensor.
OE, E3 - indicates that the water in the tank has reached the “Overflow” level and the drain pump will automatically start within 3 minutes. The reasons may be a breakdown of the drain motor, water inlet valve, level sensor or electronic controller.
UE, E4 - appears due to an imbalance of the laundry in the drum during washing. This problem is very easy to solve with the help of the optimal arrangement of things (remove the excess or add the missing). If this does not help, then the problem lies in the damage to the drum drive or electronic controller.
HE1, E5 - demonstrates problems with the water heating process. The main reason is the breakdown of the heating element, because because of this, the water temperature does not have time to increase by more than 45 ° C in 5 minutes.
HE2, E6 - indicates problems with the heating element. In this case, it is necessary to check the heating element circuit, and, if necessary, either the control module.
IE, E7 - this error on the washing machine indicates a breakdown of the water level sensor, in which the signal frequencies go beyond the upper (30 kHz) or lower (15 kHz) limit. As a result, the drain pump starts automatically. In this case, you should check the tightness of the tube that connects the sensor and the tank, as well as examine the water level sensor, if necessary, replace it.
CE, E8 - indicates that there is a mismatch in the water temperature, namely, for a certain time there was a significant temperature rise (more than 45 ° C for wool and delicate fabrics and more than 60 ° C for synthetics). As a result, the drain pump automatically starts. The reason may be a malfunction of the temperature sensor, heating element and their circuits.
LE, E9 - warns that four times there was a spontaneous drain or water leak and now there is not enough level to turn on the heater. Most often this problem occurs due to depressurization of hoses, tanks or other elements of the washing machine. It is also possible that the water leakage sensor is broken and the connection of the water drain hose should be checked for correctness.
3E, EA - indicates a break in the motor winding or tachometer. This problem manifests itself if the number of pulses from the tachometer is less than 2 in 2 seconds after the motor is turned on. In this situation, the motor or tachometer should be replaced.
BE, EB - this error on the washing machine occurs if more than 300 signals per second come from the tachometer during the washing process and indicates a thyristor circuit. To solve the problem, you must replace the engine, tachometer or control module.
tE, EC - indicates a short or open thermistor. You just need to replace the thermistor (heater sensor) with a new one.
DE, DOOR - warns of a leaky closing of the hatch door or full opening. Here you need to try to close the hatch more tightly. If it doesn’t help, you should check the operability of the hatch locking device or the electronic controller.

More recently, the washing process took a lot of time and required considerable effort. Washing units, which include the machine of the popular trademark Samsung, freed us from heavy manual labor.

Moreover, in the event of a breakdown, the self-diagnostic system of this device itself indicates the cause of the problem and the place of its localization. It is this task that Samsung washing machine error codes help to solve. Understanding the encoding is important in order to be able to effectively use the "smart" aggregate.

Information about the water level in the machine ( E7, 1C or 1E)

The Samsung washing machine has a sensor that monitors the water level - a pressure switch. If the machine displays codes E7, 1C or 1E, then the necessary information about the water level was not received from the pressure switch.

If the pressure switch tube is clogged with villi that have fallen into it, the connection between this device and the control unit may be broken: water will be drawn in, but it will not be heated

The reasons for the lack of the necessary signals may be as follows:

the pressure switch itself is out of order;
there were problems with contacts;
the sensor tube may be kinked, clogged, or punctured;
the pressure switch was installed in violation of the rules;
The problems are related to the operation of the control module.

To solve the problem, you need to get the sensor, check its tube, clean this part and install it correctly. If a sensor is damaged, it should be replaced with a good one.

If the Samsung washing machine registers incorrect frequencies for more than 5 seconds, an error lights up and the water drain turns on for 3 minutes.

Malfunctions of the engine tachogenerator ( EA, 3S4, 3S3, 3S2, 3S1, 3S, 3E4, 3E3, 3E2, 3E1 and 3E)

One of the following codes appears on the display: EA, 3S4, 3S3, 3S2, 3S1, 3S, 3E4, 3E3, 3E2, 3E1 and 3E. The machine gives them out if too much laundry has been loaded into it, if there are problems due to clogging or if there is a malfunction in the motor.

If the tachogenerator is faulty, the control module cannot determine the correct engine speed: check the resistance of the tachogenerator winding on the engine

The main reasons for the appearance of these encoding characters can be:

blocking the engine due to the ingress of foreign objects;
problems with contacts or with internal wiring;
breakdown of the tachogenerator itself;
loading laundry into the drum of the machine in excess of its maximum allowable weight;
an error made during the assembly of the engine;
incorrect operation of the control module.

Let's start the search for the true cause of the error codes on the display by unloading the laundry from the drum of the machine. Make sure its weight matches technical specifications devices. Overload must not be allowed.

Then you should check for possible places of clogging: if found, they should be eliminated. We check the quality of contacts and electrical wiring, if possible, eliminate breakdowns.

It is unlikely that a self-taught master can independently diagnose an engine breakdown and fix it. If the problem lies in the operation of the engine, you will have to seek help from specialists.

Errors in water supply E1, 4C2, 4C, 4E2, 4E and 4E1)

Do not confuse the lack of water in the car with the fact that information about its presence has ceased to flow. We have already talked about information and the sensor above, and real problems with filling the unit with water cause the following codes to appear: E1, 4C2, 4C, 4E2, 4E and 4E1.

If water does not enter the washing machine, it is imperative to check the patency of not only the hose, but also the water inlet valves

So, if it is impossible to fill the unit with water, then such a breakdown can be caused by the following reasons:

there was an emergency in the house, as a result of which the cold water supply was completely turned off;
the water supply hose is pinched, bent or clogged with something;
a clogged filter element has stopped passing liquid;
the contacts are oxidized or the water supply is not assembled according to the rules;
the protective function for the hose - Aquastop - has worked;
when connecting the washing machine to the pipes, they accidentally brought not cold, but hot water.

An effective solution to a problem depends entirely on the cause that caused it. First of all, you need to check if there is cold water in the house. To do this, open the tap, for example, in the kitchen.

Check if the tap to the hose supplying liquid to the washing machine is open. If kinks or blockages are found, they should be removed immediately. If broken parts are found, they are replaced with serviceable ones.

Problems with draining water E2, 5E or 5C)

It happens that the incorrect operation of the washing machine is manifested by the fact that the water drain in it does not work. The following symbols appear on the display: E2, 5E or 5C.

If it is difficult to drain the water from the washing machine, then it is necessary to check the outlet of the drain pump: it may be clogged with debris and foreign objects

This encoding draws our attention to the possible presence of the following problems:

some physical obstacle is resisting the drain of water from the hose: it is clogged or kinked;
the connection of the hose to the machine is incorrect;
the pump of the unit has failed;
internal wiring is broken somewhere;
clogging could have occurred not in the machine itself, but in the sewer, as a result of which draining became impossible;
plumbing fixtures were operated in violation of the temperature regime, and the water in them could simply freeze.

It is necessary to check the patency of the sewer, sniff if it smells of burnt wiring, check the hoses and change the pump if it is not working.

No signal from vibration sensor ( 8C1, 8C, 8E or 8E1)

The fact that the signals from the VRT + device have ceased to arrive, the Samsung machine will certainly display codes on its display 8C1, 8C, 8E or 8E1. All of them signal that there are problems with the correct operation of the sensor.

This sensor trigger error is caused by the following reasons:

the vibration sensor of the washing unit is out of order;
there were violations in the work of internal wiring;
the unit was assembled in violation of technical standards.

Check sensor connection contacts and wiring. Then assemble the assembly and test it in operation. If the problem persists, then the sensor itself is faulty. It should be changed.

If there are problems with the power supply ( 9C, 9E2, E91 or UC)

Washing units from Samsung have very specific requirements for power supply, indicated in the device's passport. If the declared indicators do not correspond to the actual ones, error codes may appear on the scoreboard 9C, 9E2, E91 or UC.

These are errors caused by reasons from the list below:

unacceptable power surges occur in the network;
an extension cord is used to operate the washing device;
the actual value of the voltage in the network does not meet the declared standards;
faulty control module.

If the washing machine is connected correctly, but the indicated error codes appear on the display, do not interrupt the operation of the device.

As soon as the parameters of the electrical network are brought into line with the declared ones, the device will continue its work on its own. With regular power surges, you should use a stabilizer to reduce unnecessary loads on the unit.

Communication between control modules is broken ( AC6, AC or AE)

Lack of communication between control boards can cause error codes to appear on the display board AC6, AC or AE.

A malfunction of the control module can be caused by various reasons, including a failure in the firmware, failure of triacs, tracks (microcracks) or relays

It can be assumed that the following errors became the cause of such signals:

modules were connected incorrectly;
there are defects in soldering of communication connections.

There may be a temporary network outage. Then it is enough to turn off the device, and after 15-20 seconds turn it on again. If during this time the malfunction has not resolved itself, it is necessary to contact the service center to replace the control module.

Control panel buttons ( EB, BC2, bE3, bE2, bE1 and bE)

On the control panel of the washing device there are switches with which the user selects the washing mode. These buttons can also break over time. Error codes will indicate breakdowns of this kind. EB, BC2, bE3, bE2, bE1 and bE.

These signs on the display signal us about malfunctions of this kind:

the buttons began to sink or stopped being pressed;
the control panel is screwed too tightly;
the internal parts of the panel, made of plastic, have lost their original shape (deformed);
there are problems with the relay: it is not connected correctly or has stopped closing.

To try to unlock the device, you should press the sunken or sticky buttons. Disconnect the machine from the network, and then try to turn it on again. If these actions did not lead to the desired result, and the codes continue to be displayed, you need to call the service center and call the wizard: you will not be able to cope with this problem on your own.

When hot water drains AC6, AC or CE)

The device must not drain too hot water. If this happens, error codes are shown on the display screen AC6, AC or SE.

These codes warn that the following might have happened:

the machine was mistakenly connected not to cold, but to hot water;
the temperature sensor no longer works.

You need to check if the device is connected correctly. If this error is excluded, it remains only to buy and install a new temperature sensor.

Manhole door malfunctions ( ED, DC2, DC1, DC, dE2, dE1,dE)

During the washing process, the hatch door of the washing machine must be tightly closed. If this does not happen, then the following symbols can be seen on the scoreboard: ED, DC2, DC1, DC, dE2, dE1, dE.

The door lock problem is one of the most common malfunctions: first of all, you should check the operation of the lock mechanism itself

The reasons for their appearance are as follows:

the hatch door is not closed tightly enough;
the hatch blocking mechanism is out of order;
during the boiling process, the door was displaced;
they tried to open the hatch with the use of force and damaged it;
the sunroof lock connector was installed incorrectly;
the sunroof sensor turned on spontaneously during the vibration of a running machine;
An error has occurred in the control module.

Before contacting the workshop, you should find out if error codes have appeared due to an insufficiently well-closed door. To do this, open the hatch, and then close it again. It is necessary to check if debris or a corner of dirty laundry has got into the blocking device. If these measures do not lead to the desired result, you should call the master.

Errors when turning on the ventilation mode ( FC or FE)

If the device has a drying mode, then codes may appear on the display FC or F.E..

So the system can respond to the following malfunctions:

wiring has been damaged.
the connector has come out of the place where it was originally installed;
the blades are blocked due to the lack of their lubrication and the ingress of various debris into the device;
the start capacitor is broken.

The problem is not as simple as it might seem at first glance, so call the wizard and do not suffer. It is easier to pay than to break and then buy a new washing machine.

The heating element has failed E6, E5, HC2, HC1, HC, H2, H1, HE3, HE2, HE1 and HE)

It will not be a revelation to anyone that there is a heating element in the washing device - a heating element, with the help of which the water acquires the temperature necessary for washing things. Errors in the operation of the heater are manifested by the appearance of codes E6, E5, HC2, HC1, HC, H2, H1, HE3, HE2, HE1 and HE.

Faulty, all covered with scale, the heater needs to be replaced. Not only hard water can lead to its breakdown, but also the regular use of baby powders, which include soap.

They appear on the scoreboard as a result of the following problems:

there are malfunctions in the operation of the internal network caused by a wire break or short circuit;
the tubular electric heater (TEH) is broken;
the temperature sensor has failed;
errors occurred during the steam function;
the machine is not properly connected to the mains.

In such a situation, there is little you can do yourself, except to check that the unit is connected to the mains correctly. If everything is in order with this, and the codes continue to be displayed on the scoreboard, call a specialist.

Water leak occurs E9, LC, LE1 and LE)

Code errors E9, LC, LE1 and LE appear on the display if the machine spontaneously leaks water.

The reason for the spontaneous draining of water in the washing machine may be the wrong location of the drain hose and its incorrect connection to the sewer

This situation can happen due to a number of reasons:

drain hose position too low;
the drain hose is not properly connected to the sewer;
the seal, drain hose or tank itself is leaking;
the fastening of the heating element has weakened;
too much foam appeared during the washing process due to excess detergent or the use of a detergent with a high level of foaming;
the pump cover is installed in violation of the rules;
defective leak sensor

Disconnect the machine from the power supply, change the position of the drain hose, check the condition of the seals, tank and hose. If the cause of the malfunction is not identified at this stage, and the error code still appears, it is time to show the washing unit to the master.

You can see one of the successful drain device options in this diagram. To avoid unnecessary stressful situations, follow our tips

When there is too much water E3, 0C, 0F or 0E)

If during the washing process more water is poured into the machine than necessary, one of these codes can be seen on the display: E3, 0C, 0F or 0E.

Their appearance may indicate the following:

the drain hose is not connected correctly;
the valve that regulates the flow of water is blocked;
the water level sensor is broken.

You can try to avoid this error by turning off the machine and then lowering the drain hose into the tub. Run the wash in the desired mode. If the error reappears on the display, contact the repair shop.

Errors in the operation of the temperature sensor ( EU, TC4, TC3, TC2, TC1, TC, tE3, tE2, tE1)

If the following signs are displayed on the scoreboard: EU, TC4, TC3, TC2, TC1, TC, tE3, tE2, tE1, This means that the temperature sensor is not working properly.

Such a malfunction can be caused by the following reasons:

Faulty or incorrectly installed temperature sensor;
the tubular heater (TEN) has failed;
internal wiring not working.

These problems cannot be fixed by yourself. Please contact the service center.

The device has overheated ( HER)

Typically, such a malfunction occurs in those machines that are equipped with the function of drying washed laundry. When it occurs, a code appears HER.

The reason may be:

drying temperature sensor malfunction;
damage to internal wiring (break);
failure of the drying heater.

Call the wizard, since these violations in the operation of the device cannot be eliminated on your own.

Unbalance error codes ( E4, UB or UE)

If the display lights up E4, UB or UE, then the device is out of balance.

Imbalance during washing can significantly reduce the life of your washing machine: distribute the laundry inside the device as evenly as possible

The reasons for this violation are:

the laundry was unevenly distributed over the drum during washing;
the balance of the unit itself is disturbed.

All laundry should be evenly distributed inside the drum, and also, following the instructions, try to balance the device.

Excess foam during washing ( SD, 5D, SUDS or sud)

If too much foam has formed during the wash, the codes will inform you about it SD, 5D, SUDS or Sud.

The use of detergents atypical for this purpose, such as hair shampoo, can also lead to the formation of a large amount of foam during the washing process.

Excess foam can form for the following reasons:

too much washing powder is poured into the receiver;
your powder is not suitable for this washing machine;
The wrong quality detergent was used during washing.

If the foam is within the device without breaking out, you can do without turning off the device. Wait until it shrinks and continue washing. After use, be sure to clean the filter. If the foam falls out, the unit will have to be turned off, the laundry removed, and the filter cleaned immediately.

To check once again how much you remember the malfunctions corresponding to the Samsung washing machine error codes, watch this video:

Let it be your guide in case of an emergency.

Thanks to error codes, you can quickly find the problem and try to fix it. Some problems can be fixed quite easily by yourself. If you cannot do this quickly and independently, you should seek help from professionals.

Owners of Samsung washing equipment sometimes encounter a situation where a loaded washing machine stops and a message appears on its electronic display stating that a 5d error has occurred on the Samsung washing machine. A large amount of foam can be observed through the glass. An error has occurred during operation. How serious is she? Can you handle it yourself? What can be done to correct the current situation?

What happened

This code is issued in cases where too much foam has formed - much more than usual. On some machines, another code may be indicated in such a situation: SUD, SD. The exact name depends on the brand of the car.

This could be due to one of the following reasons:

As you know, not all types of washing powder are designed for use in such machines. If in this case one that was intended for manual processing was used, then this could well cause increased foaming and lead to a stop in the operation of the machine.
Unfortunately, some of those that are commercially available are of insufficient quality. If one of them was used in the wash, it could cause error code 5d to appear.
To do this, it was enough to pour too much powder.

Before you apply it, you need to familiarize yourself with what type of processing it is intended for. When buying, you need to choose a brand that has enough high quality for use in a specific washing machine. Be sure to look at the packaging and familiarize yourself with which portion should be loaded.

Sometimes the problem is not in the powder chosen for washing, but in other things.

If the drain filter is clogged, this can cause this problem. Poor draining in this situation does not make it possible to remove the foam in time.
When washing clothes that contain porous fabrics, increased foaming is sometimes possible.
When it comes to fluffy things, this situation also creates more foam.
The water level sensor or the one that controls the level of foaming has broken.
The control unit is faulty, which means that you need to contact a specialist. In this situation, you need to call a repairman.

In cases 2 and 3, it is necessary to reduce the rate of use of the powder compared to the usual one.

How to proceed

This type of error does not pose a serious danger to either the washing machine or the laundry being processed. In most cases, it is provided that the removal of excess foam is carried out automatically.

Some brands provide for the removal of excess foam after pressing the “Start / Pause” button on the machine panel.

It is important to understand that an excessive amount of powder used does not lead to an increase in the quality of washing. It will be the best option if the portion is exactly the same as indicated on the package.

Unfortunately, there is another option. If everything is done correctly, but excess foam still appears, then this is not an insurmountable problem. It is enough just to correct the loaded norm. In such a situation, you need to lay less powder than before.

If, despite the measures taken, the problem continues to occur, then you need to consult with specialists.

Other options

In some situations, events develop differently. It may turn out that a failure signal is displayed on the screen, at the same time, the washing does not stop. What to do in this case?

First of all, you need to finish washing and turn on the drain. After stopping work, open the door. Now you need to clean the drain filter.

Then, to complete the cleaning process, you will need to start the washing machine again, but without detergent and laundry.

After everything has been done, we can assume that the cleaning of the machine is completed. Now you can continue the washing process in the usual way.

If an error occurs, but the foam is not visible, most likely in this case we are talking about the fact that there is a malfunction in the machine that a specialist must fix. However, it will not be superfluous to first start the machine without using powder and without laundry. Thus, it will be further cleaned and this will increase the chances that this error will not happen again.

If a master was called to repair

So far, we have considered actions that the owner of the car could do on his own. Unfortunately, this is not always possible. Next, situations will be considered when calling a specialist.

If there is no foam, but a malfunction occurs, the likely cause is that the foam sensor has failed. It needs to be changed. The usual price in this case is in the range from 3000 to 4500 rubles.
Such a problem may be present immediately after switching on. Sometimes it works at a random moment in time. The fact is that for some Samsung machines, the sensor that reacts to increased foaming is the same one that measures the water level during washing. It's called a pressure switch. In other words, giving an error, it reacts not to the amount of foam, but to the water level. In such a situation, the pressure switch will have to be changed. It will cost from 2900 to 3900 rubles.
In some cases, washing can be done without powder. If the washing machine does not give the error in question, but when washing with powder and a fully loaded tank, an error appears, then you can most likely expect a blockage in one of the elements of the drain system. It can be a drain filter, a hose or a sewer. Then you will need to clean the drain. The cost of work in this case can pull from 1000 to 2500 rubles.
With a normally loaded washing machine, the control unit gives an error during operation. If after that you start the process without washing powder and without laundry, the error continues to appear. In this case, you will have to assume that the control unit of the washing machine is faulty. Work with this type of repair will cost in the range from 3800 to 5500 rubles. Replacing the power supply will cost 7000 rubles.

Conclusion

When using washing machines, failures and breakdowns are not excluded. At the same time, you need to understand what can happen, how to fix yourself, and when you need to call a specialist for repairs.

A large manufacturer of household appliances Samsung cares not only about its product, but also about consumers. So in washing machines from this firm programming codes, which are displayed on the machine's display in the event of an error. Such codes provide enough useful information to understand the cause and fix the problem. We suggest that you familiarize yourself with the 5d error on the Samsung washing machine, the reasons for its occurrence and preventive measures.

Decoding error 5d

There are a lot of models of washing machines manufactured under the Samsung brand. Most of them have the same error code name. However, there are codes that indicate the same error. For example, codes 5d,sud orsudS are different names for the same error.

Samsung washing machine error 5d means that too much foam has formed inside the drum.

Causes

Increased foaming in the washing machine can be caused by the following reasons:

Instead of automatic washing powder, hand washing powder was used. Hand washing powder lathers a lot. Powders labeled "automatic" contain foam stabilizers that dampen excessive foam formation. This is necessary so that the foam does not fall on the electric motor and does not come out.
The powder "Automatic" used for washing turned out to be of poor quality.
Exceeding the required amount of powder per wash cycle.

Troubleshooting and Precautions

Error 5d generally does not require any action. Usually the machine automatically removes the foam, or waits for it to settle. Then the wash continues. In some models, to actively eliminate foam, you need to press the "Start (Pause)" button on the machine panel.

In order to avoid such an error, you need to use only highly effective powders or liquid detergents. At the same time, there must be a mark on the packaging that the product is suitable for an automatic machine.

Important! Be sure to look at the detergent packaging for how much powder is recommended for one wash cycle.

The correct dosage will not only save the machine, but also save money. Remember that if you pour more powder, then it is not necessary that it washes clothes better. Therefore, always use a measuring container when pouring powder into the washing machine.

If you are doing everything right, but the error still appears, try pouring a little less powder the next time you wash it. If this does not lead to the desired result, then you should seek the advice of professionals from service center Samsung.

Error 5d on the display of the washing machine is not critical. In most cases, it is eliminated within a few minutes. There are more serious error codes that appear during washing, you can find them in the article:. Also watch the video.